PLASTILINE® MMA Cold Plastic Roller
PLASTILINE® MMA Cold Plastic Roller is a two-component, solvent-free MMA cold plastic marking system, factory-pigmented to the specified RAL Traffic Colour. Applied by roller, smooth squeegee or brush, it produces solid-colour markings with sharp edge definition, rapid curing and long-term outdoor durability for decorative and functional traffic areas.
Available in 5Lt & 20Lt
Features & Benefits
- 100% solids, solvent-free formulation
Provides a high-build marking with no shrinkage caused by solvent loss during cure. - Ultra-low VOC
Mixed VOC content of only 2.1 g/L, below the stated zero-VOC threshold of 5 g/L. - Factory pre-pigmented
Component A is supplied pre-blended to the specified RAL Traffic Colour, eliminating on-site pigmentation. - Rapid curing
Hardens in approximately 30 minutes at 20°C and can be trafficable within one hour. - Cold-tolerant cure
Can cure at ambient temperatures down to 10°C, extending the workable application season. - Permanently elastic
Accommodates substrate movement without cracking throughout the marking's service life. - UV stable
Colourfast pigments provide good outdoor colour retention. - Smooth matt finish
Produces a consistent decorative and functional traffic-marking surface. - Sharp edge definition
Particularly suited to linework, parking-bay edges, kerbs and hatched areas where clean delineation is important. - Bitumen compatible
Designed to resist bleed-through on asphalt, including new asphalt after the specified minimum 14-day curing period. - Hydrophobic surface
Helps reduce dirt retention. - Anti-blackening compatible
PLASTILINE® MMA Anti-Blackening can be applied as an optional topcoat where resistance to tyre rubber and bitumen contamination is required. - Optional anti-skid capability
Broadcast aggregate or PLASTILINE® Reflective MMA Reactive Beads can be added to the wet coating where anti-skid performance is specified. - Long service life
The datasheet states an expected five to ten-plus years on high-traffic surfaces, subject to traffic volume and specification compliance.
Intended Uses
PLASTILINE® MMA Cold Plastic Roller is intended for single-coat, solid-colour area and line marking where a durable MMA cold plastic finish is required without built-in anti-skid aggregate.
The system is suitable for asphalt and correctly prepared and primed concrete, as well as other substrates when used with the appropriate PLASTILINE® or PLASTISEAL® primer system.
Its combination of factory-controlled colour, rapid curing and sharp edge definition makes it suitable for both functional traffic delineation and decorative coloured surfacing.
Where additional anti-skid properties are required, suitable aggregate or PLASTILINE® Reflective MMA Reactive Beads can be broadcast into the wet film before curing.
Typical Applications:
- Parking bays
- Parking-bay edges
- Taxi ranks
- Bus stops
- Passenger drop-off zones
- School zones
- Pedestrian plazas
- Public-realm areas
- Decorative coloured streetscapes
- Bicycle paths
- Shared-use trails
- Kerbs
- Hatched traffic markings
- Traffic linework
- Coloured asphalt areas
- Primed concrete areas
- Tennis court markings
- Padel court markings
- Basketball court markings
The product is particularly suited to applications requiring solid colour and sharp edge definition. Bicycle paths and shared-use trails are specifically identified where built-in anti-skid is not required, while court markings can be factory-pigmented to the required court-line RAL colour.
Technical Information:
- Product Type: Two-component methacrylate (MMA) resin system
- Product Tier: Pre-pigmented roller-applied area marking with no built-in aggregate
- Finish: Smooth matt
- Standard Colours: 10 standard RAL Traffic Colours
- Traffic White: RAL 9016
- Traffic Black: RAL 9017
- Traffic Yellow: RAL 1023
- Traffic Orange: RAL 2009
- Traffic Red: RAL 3020
- Traffic Purple: RAL 4006
- Traffic Blue: RAL 5017
- Traffic Green: RAL 6024
- Traffic Grey A: RAL 7042
- Traffic Grey B: RAL 7043 - Custom Colours: Custom RAL and pigment-matched colours available on request
- Specific Gravity – Mixed: 1.326 kg/L
- Mass Solids: 100%
- Volume Solids: 100%
- VOC Content – Mixed: 2.1 g/L
- Hardness: Shore D 45–55
- Component A: PLASTILINE® MMA Cold Plastic Roller, factory pre-pigmented and pre-blended
- Component B: PLASTILINE® MMA BP 50 Hardening Powder
- Mixing Ratio by Weight: Component A : Component B = 100 : 0.5–3.0, temperature dependent
- Application Methods: Roller, smooth squeegee or brush
- Number of Coats: 1
- Wet Film Thickness: 0.5–1.5 mm per coat
- Application Rate: 0.7–2.0 kg/m² depending on substrate texture
- Theoretical Consumption: Approximately 1.33 kg/m² per 1 mm wet film
- Air Temperature: 10–35°C
- Substrate Temperature: 10–40°C
- Dew Point Requirement: Minimum 3°C above dew point throughout application and cure
- Pot Life at 20°C: Approximately 14 minutes using 2% Component B
- Trafficable at 20°C: Within 1 hour of application
- Tool Cleaning: Acetone immediately after use; never use on a cured surface
- Component A Pack Sizes: 5 L tin (5 kg net) and 20 L tin (20 kg net)
- Component B Pack Sizes: 10 g, 30 g, 80 g, 100 g, 200 g and 700 g
- Storage Temperature: 5–25°C
- Shelf Life: 12 months from manufacture in the original unopened container
Standard Colours
RAL 9016
Traffic White
RAL 9017
Traffic Black
RAL 1023
Traffic Yellow
RAL 2009
Traffic Orange
RAL 3020
Traffic Red
RAL 4006
Traffic Purple
RAL 5017
Traffic Blue
RAL 6024
Traffic Green
RAL 7042
Traffic Grey A
RAL 7043
Traffic Grey B
Custom RAL
Pigment-matched colours available on request
Please Note: Colour swatches and illustrations displayed are only to be used as a guide and can vary from the original.
